日本免费全黄少妇一区二区三区-高清无码一区二区三区四区-欧美中文字幕日韩在线观看-国产福利诱惑在线网站-国产中文字幕一区在线-亚洲欧美精品日韩一区-久久国产精品国产精品国产-国产精久久久久久一区二区三区-欧美亚洲国产精品久久久久

  1. 首頁 > 云知道 > >

CISCO路由器初始配置簡介

云知道

很多初學路由器知識的網友對路由器的初始配置可能感到很生疏,本人在初學時也很困惑,因?yàn)橐幌鲁鰜?lái)很多提問不知如何是好,下面將最近剛調試的一臺CISCO3640的初始配置整理出來與各位網友交流,如有疏漏之處,還請大家指正 。
1.用CISCO隨機帶CONSOLE線,一端連在CISCO路由器的CONSOLE口,一端連在計算機的COM口 。
2.打開電腦,啟動超級終端.為您的連接取個名字,比如CISCO_SETUP,下一步選定連接時用COM1,下一步選定第秒位數9600,數據位8,奇偶校驗無,停止位1,數據流控制無.最后選確定 。
3.打開路由器電源,這時超級終端將出現以下畫面:
System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.C3600 processor with 32768 Kbytes of main memory Main memory is configured to 64 bit mode with parity disabled
rogram load complete, entry point: 0x80008000, size: 0x4ed478 Self decompressing the image :;
###################################################################
###################################################################
###################################################################
###################################################################
###################################################################
###################################################################
###################################################################
[OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
ubject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software;
IOS (tm) 3600 Software (C3640-I-M), Version 12.1(2)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Tue 16-May-00 12:26 by ccai
Image text-base: 0x600088F0, data-base: 0x60924000
cisco 3640 (R4700) processor (revision 0x00) with 24576K/8192K bytes of memory.
Processor board ID 25125768
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: y
您是否進入初始化配置對話,選Y
At any point you may enter a question mark "?" for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets "[]".Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system
Would you like to enter basic management setup? [yes/no]: n
您是否進入基本配置安裝,選N
First, would you like to see the current interface summary? [yes]: y
首先,您是否看一下當前端口狀態
Any interface listed with OK? value "NO" does not have a valid configuration
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0unassigned NO unset up down
Serial0/0 unassigned NO unset down down
FastEthernet0/1unassigned NO unset up down
Configuring global parameters:
Enter host name [Router]:RouterA
輸入路由器的名字
The enable secret is a passWord used to protect Access to
rivileged EXEC and configuration modes. This password, after

推薦閱讀